Inton Systemkonzept

CTRL: The system controller is the central control unit of the Inton system and is connected to other parts of the system installation via IP-network. In most use cases only one or two controllers are needed per installation.

LINK: The AL3-IP-Link connects an AL3-chain with the IP-network. Due to the limitation of the number of componenets in one AL3-chain (max. 40 modules per chain) you need at least one AL3-Link per 40 modules.

TCS: Touch-Call-Station is a call station console with a touch display, that is connected to the system via IP-network.

AL3: Al3 stands for "Low-Latency-Audio-Link". It is a fast audio connection with a bandwidth of 64 channels of uncompressed audio (24bit/48kHz) with a maximum latency of 0,1ms over the whole Al3-chain. In additio to audio transport, there are also control signals transmitted over Al3.

A: The analog audio module features eight analog audio inputs and outputs. It is one of the modules that are chainable via AL3 and allows you to add as many analog inputs and outputs to the installation as you need.

PAC: The power amplifier controller allows you to integrate a four-channel 100V-amplifier into the installation and monitors it. The PAC is chainable via AL3 which gives you the power to add as many amp channels to the system as you like. Note: the four 100V-outputs of the PAC do not have a line relais. If you need line-relais (i.e. because you want to share one amp-channel between multiple lines) we are currently developing a separate relais module for that purpose that allows you to flexibly do that and also to do hot replacement of amplifier chanels in the failure case (amp backup).

AES: The AES-EBU module allows you to connect up to four AES-EBU call stations into the system. The AES module is chainable via AL3 practically allowing you to add all the call stations you need to the installation.

Efficient cabling with the new AL3 bus

Inton ist highly modular and still very simple to install. The innovative high-speed audio bus AL3 allows to use standard network cables to interconnect between system modules in a "daisy chain fashion". If you wonder how AL3 differs from other popular audio distribution network solutions like Dante, you should note that AL3 does not require costly network switches and no IP-addresses. This means you can have a lot of modules without having to worry about IP addresses and if that weren't already cool enough the modules on the AL3-bus are self organizing. It means that it does not matter at all in what order the components are chained, they will always work just like they were configured to. This is very important if you want to be able to to hot exchange of faulty components while keeping the rest of the network live.

The cost effective and simple cabling is what really empowers the highly modular system design. In turn, the fine grained modularisation has a positive effect on the installation cost because there is always just the right amount of inputs and outputs, call stations and amplifier channels.

AL3 can span up to 100m between modules using CAT5-cable (resulting in a max. AL3-chain length of 4km). If you use media converters and fiberglass cable the distance between two AL3 modules can be multiple kilometres which makes the AL3-bus very attractive for tunnels, train lines and other geographically widely spread installations.

Note that the AL3-bus is particularly well suited for tunnel installations, where you usually have amplifiers that are installed at constant distances throughout the tunnel which have to send audio with an individual delay on each channel, that is entirely depending on the position of the speaker in the tunnel, in order to avoid acoustic interferences like audio cancellation.

Even if you go to the maximum number of modules per bus, AL3 guarantees sample-synchronous audio accross all these modules. The delay between the two ends of the chain is always below 0,1 milliseconds, which is significantly below what human hearing can differentiate.

Decentralized Installation

Inton uses standard Ethernet cable (i.e. CAT5) for connecting its components. This allows a decentralized system installation where one or many components are broken out via AL3 or LAN/WAN.

Since AL3 is IP layer 1 it must not be routed over conventional switches. This means that the AL3-chains can not share the same cable installation as the rest of the IT. This can be a blessing because the IT can not influence the audio installation and vice verca. But sometimes it is not feasible to pull in extra cables for AL3, so we provide an alternative way of decentralized installation that makes use of existing IT cabling: Wherever the audio has to be routed over a conventional IP network with routers and switches you can convert AL3 via the AL3-IP-Link modules to an IP audio stream. Of course the ultra-low latency can not be kept up over switches and routers.

Break out modules over AL3 if pulling a separate cable is easily possible or if there is no existing IP-infrastructure. The advantage of AL3 is that you don't need any switches at all.

To break out modules over IP-network (LAN / WAN) makes sense, if the network should be shared with IT components or if it would not be economically feasible to pull separate cables for the audio.

Kostenvorteil durch niedrigen Energieverbrauch

Inton ist energieeffizient. Dies ist nicht nur aus ökologischen Gründen besser, sondern erfordert weniger Kühlung (Schrankklimatisierung) sowie kleinere Batterien für den Notbetrieb. Die Notstromaggregate sind ein nicht unwesentlicher Kostenfaktor einer Evakuierungsanlage, die bei Stromausfall bis zu 72 Stunden weiter betriebsbereit bleiben muss.

Bei Stromausfall bleibt eine Kleinanlage bestehend aus Controller, Al3-IP-Link, PAC und 4-Kanalverstärker mit zwei Standard-Autobatterien 144 Stunden lang im Standby-Modus weiter Betriebsbereit, sogar 72h Normalbetrieb sind möglich.

Anders herum betrachtet, kann bei Stromausfall mit zwei Standard-Autobatterien (um 24V zu erreichen) eine Installation mit 12 Kreisen 72 Stunden lang im Standby-Modus betriebsbereit bleiben.

Je größer die Installation, desto mehr Batterien werden benötigt. Diese müssen untergebracht, gewartet und ersetzt werden. Aus diesem Grund ist Energieeffizienz ein nicht zu vernachlässigender Kostenfaktor sowohl bei der Anschaffung als auch im Betrieb.

Gute Skalierbarkeit durch modulares Systemdesign

Inton ist durch seinen hohen Modularisierungsgrad extrem gut skalierbar. Das bedeutet, dass mit geringer Basisstruktur durch hinzufügen entsprechender AL3-Module eine sehr große Anzahl an Verstärkerkanälen, Sprechstellen, analogen Ein- und Ausgängen etc. erreicht werden kann.

Aus dieser Eigenschaft kann sich ein enormer Kostenvorteil ergeben, z.B. im Vergleich zu Systemen, die für je vier weitere Verstärkerkanäle einen weiteren Controller benötigen.

Das oben dargestellte System ist bereits sehr groß, dabei geht es noch nicht einmal annähernd an die Grenzen des Möglichen. Je nach Bedarf können weitere Al3-IP-Links hinzugenommen werden und eröffnen ihrerseits die Möglichkeit für weitere 40 Module je nach Wahl. Aber Inton skaliert nicht nur nach oben sehr gut. Es eignet sich auch für kleine Installationen: